View LA71525M_106727.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : EN5843
LA71525M
Monolithic Linear IC
LA71525M
Video/audio signal processor for VHS VCRs (single chip for Y/C/A)
Overview
The LA71525M is a video/audio signal processor IC for VHS VCRs. It handles recording and playback of PAL/GBI, MESECAM, and 4.43 NTSC signals. NTSC software tapes can be converted to PAL for monitoring, and the IC realizes high picture and sound quality. The IC requires no adjustments and minimizes the peripheral component count, making it possible to implement efficient signal handling at low cost.
Package Dimensions
unit: mm 3174-QFP80E
[LA71525M]
0.8
1.0
0.8
23.2 20.0 0.35 41
1.6 0.15
64 65 40
17.2 14.0
0.8
1.6
80 1 24
25
0.8
2.70
3.0max
21.6
0.8
Specifications
Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Symbol VCC max VCC max Allowable power dissipation Pd max pin 36, 41, 47 pin 76 Ta 65C 114.3 x 76.1 x 1.6 mm 3 with paper phenol substrate Operating temperature Storage temperature Topr Tstg Conditions
SANYO : QFP80E (QIP80E)
15.6
Ratings 7.0 9.0 1400
Unit V V mW
-10 to +65 -40 to +150
C C
Operating Conditions at Ta = 25C
Parameter Recommended supply voltage Symbol VCC1 VCC2 (VCC2) Recommended operating supply voltage range VCC1 opg VCC2 opg Conditions pin 36, 41, 47 pin 76 (pin 76) Ratings 5.0 6.8 (7.5) 4.8 to 5.5 6.4 to 7.9 Unit V V V V V
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co., Ltd. Semiconductor Business Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
31799RM(KI) No. 5843-1/25
LA71525M
Operating Characteristics at Ta = 25C, VCC = 5V
Parameter [REC mode Y] Current drain (POWER SAVE MODE) Current drain (REC) EE output level 1 EE output level 2 AGC characteristics 1 AGC characteristics 2 AGC characteristics 3 AGC characteristics 4 Sync separation output level Sync separation output pulse width Sync separation output Pre-delay time Sync separation output Threshold level Sync tip level Pedestal level White level measurement Symbol Input Output Conditions Ratings
min
20 130 2.0 2.0 0 -1.2 550 370 4.0 4.2 0.6
typ
22 145 2.1 2.1 0.6 -0.2 650 420 4.2 4.5 0.8 -20
max
24 160 2.2 2.2 1.2 0
Unit
ICCS ICCR VEE1 VEE2 AGC1 AGC2 AGC3
T28A T28A T28A T28A T28A T28A T28A T38 T38 T38 T38 T38 T38 T37 T37 T37 T37 T38
Influx current measured at pin 41 in power save mode Sum of influx current at pins 36, 41, 47, 76 measured; 5V: pins 36, 41, 47; 7V: pin 76 T38 output level measured with VIN = 1.0 Vp-p video signal (PAL) T38 output level measured with VIN = 1.0 Vp-p video signal (NTSC) Ratio of VEE and T38 output level with VIN = 2.0 Vp-p video signal Ratio of VEE and T38 output level with VIN = 0.5 Vp-p video signal T38 SYNC level measured with VIN = 700 mVp-pLUMI, 600 mVp-p SYNC T38 SYNC level measured with VIN = 700 mVp-pLUMI, 150 mVp-p SYNC T37 output pulse crest value measured with VIN = 1.0 Vp-p video signal T37 output pulse width measured with VIN = 1.0 Vp-p video signal Delay of output SYNC vs. input SYNC measured with VIN = 1.0 Vp-p video signal Input level gradually attenuated and measured when output pulse width becomes larger than PWSYR by 1 s Potential measured with VIN = 1.0 Vp-p video signal, under following conditions. T38 sync tip level: LSYN Pedestal level: LPED White peak level: LWHT
mA mA Vp-p Vp-p dB dB
750 mVp-p 470 mVp-p 4.4 4.8 1.0 -15 900 Vp-p s s dB mV
AGC4 VSYR
PW SYR T28A TSYR THSYR LVOR
T28A T28A T28A
700
800
Simulated H insertion level
HDR
T28A
T38
T38 DC level measured with 2.7V DC applied to T33. Using this as LHDR, differential to LPED (see above) is calculated. T38 DC level measured with 1.3V DC applied to T33. Using this as LWHR, differential to LWHT (see above) is calculated. T25 YNR characteristics measured with VIP = 1 Vp-p standard color bar signal input Serial 00 OFF 10 (weak) 01 (medium) 11 (strong)
-150
0
+150
mV
White insertion level
WHR
T28A
T38
-150
0
+150
mV
REC YNR operation
RYNR
T28A
T25
0 1.7 4.2 / -0.3 -1.4 -4
0 2.7 5.7 / +0.2 -0.4 -2
0 3.7 7.2 / +0.7 +0.6 0 -25 dB dB dB dB dB
YLPF frequency response characteristics 1 YLPF frequency response characteristics 2 YLPF frequency response characteristics 3 YLPF frequency response characteristics 4
REC-FM output level Carrier frequency 1 (PAL) Carrier frequency 2 (NTSC)
YLPF1 YLPF2 YLPF3 YLPF4 VFM FFM 1 FFM 2
T28A T28A T28A T28A
T25 T25 T25 T25 T18 T18
1 MHz response of T25 vs. 500 kHz with VIN = 1 Vp-p standard multiburst signal 2 MHz response of T25 vs. 500 kHz with VIN = 1 Vp-p standard multiburst signal 3 MHz response of T25 vs. 500 kHz with VIN = 1 Vp-p standard multiburst signal 4.43 MHz response of T25 vs. 500 kHz with VIN = 1 Vp-p standard multiburst signal T18 output level measured in no-signal input condition T18 output frequency measured in no-signal input condition
304 3.725 3.325
320 3.8 3.4
336 mVp-p 3.875 3.475 MHz MHz
Continued on next page
No. 5843-2/25
LA71525M
Continued from preceding page
Parameter REC-FM output level Secondary distortion Deviation 1 (PAL) Deviation 2 (NTSC) FM modulator linearity Symbol Input Output T18 T28A T28A T26 T18 T18 T18 T18 T26A T26A T24 T37 T24 Conditions Secondary distortion measured in no-signal input condition Ratings
min
typ
-40
max
-35 1.05 1.05 +2 9.1 +0.25 1.1
Unit dB MHz MHz % kHz dB dB
HMOD DEV1 DEV2 LMOD CS GEMP24 GEMP37 GENH1
T18 deviation measured with VIN = white 100% 1 Vp-p T18 deviation measured with VIN = white 100% 1 Vp-p
Output frequency set to f2.85 with 2.85V DC applied to T26 Output frequency shift
0.95 0.95 -2 6.5 -0.75 0.1
1.00 1.00 0 7.8 -0.25 0.6
1/2fH carrier shift
Emphasis gain Detail enhancer characteristics 1 Detail enhancer characteristics 2 Detail enhancer characteristics 3 Nonlinear emphasis characteristics 1 Nonlinear emphasis characteristics 2 Nonlinear emphasis characteristics 3
Level difference of T26A and T37 measured with VIN = 500 mVp-p, 10 kHz sine wave input Level difference of T26A and T37 measured with VIN = 158 mVp-p, 2 MHz sine wave input Differential with GEMP24
GENH2
T26A
T24
Level difference of T26A and T24 measured with VIN = 50 mVp-p, 2 MHz sine wave input Differential with GEMP24
1.3
2.3
3.3
dB
GENH3
T26A
T24
Level difference of T26A and T24 measured with VIN = 15.8 mVp-p, 2 MHz sine wave input Differential with GEMP24
1.8
3.3
4.8
dB
GNLEMP1 T26A
T24
Level difference of T26A and T24 measured with VIN = 500 mVp-p, 2 MHz sine wave input Differential with GEMP24
0.3
1.2
2.1
dB
GNLEMP2 T26A
T24
Level difference of T26A and T24 measured with VIN = 158 mVp-p, 2 MHz sine wave input Differential with GEMP24
2.5
3.8
5.0
dB
GNLEMP3 T26A
T24
Level difference of T26A and T24 measured with VIN = 50 mVp-p, 2 MHz sine wave input Differential with GEMP24
Serial 1 2 3 4
6.5 4.5 2.5 0 10.5
8.0 6.0 4.0 0 11.0
9.5 7.5 5.5 0 11.5 dB dB
Main linear emphasis characteristics 1 Main linear emphasis characteristics 2 White clip level Dark clip level Video output linearity
GME1
T26A
T37
Level difference of T26A and T37 measured with VIN = 50 mVp-p, 500 kHz sine wave input Differential with GEMP37
GME2
T26A
T37
Level difference of T26A and T37 measured with VIN = 50 mVp-p, 2 MHz sine wave input Differential with GEMP37
12.5
13.0
13.5
dB
LWC LDC LINY
T28A T28A T28A
T37 T37 T38
White clip level at T37 measured with VIN = white 100% 1.0 Vp-p Dark clip level at T37 measured with VIN = white 100% 1.0 Vp-p
CTL 1 2 CTL 1 2
185 176 -57.5 -52.0 -0.5
195 185 -52.5 -47.0 0
205 194 -47.5 -42.0 +0.5
% % dB
T38 stair levels measured with video signal 1.0 Vp-p (linearity unit, 5 stairs) input. Stair linearity determined by arithmetic processing.
[PB mode Y] Current drain PB Dropout compensation time
ICCP T DOC
T15 T26A T38
5V: pins 36, 41, 47; 7V: pin 76 Sum of influx current at pins 36, 41, 47, 76 measured T20: 4 MHz, 300 mVp-p sine wave T26A: revert time for T38 output from when 0.5 Vp-p video signal T15 input is set to 0 T38 T15: 4 MHz, 300 mVp-p sine wave T26A: 0.5 Vp-p video signal Input/output response 5H after setting T15 input to 0 T38 T38 Playback Y level with DEV = 1.0 MHz FM signal input Playback Y level for self-recording/playback
153 10.5
170 12.5
187 14.5
mA H
DOC characteristics
GDOC
T15 T26A
-1.5
0
+1.5
dB
PB Y level Self-recording/playback Y level
V-YOUT R/P-OUT
T15
2.00 1.93
2.10 2.10
2.20 2.27
Vp-p Vp-p
Continued on next page
No. 5843-3/25
LA71525M
Continued from preceding page
Parameter FM demodulator linearity Symbol Input T15 Output T25 Conditions Ratings
min
-3.5
typ
0
max
+3.5
Unit %
LDEM
LDEM =
Carrier leak Playback YNR characteristics
V DEM4 - (VDEM2 + V DEM6 ) /2 V DEM6 -VDEM2
x 100
-35 dB
CL PYNR
T15 T26A
T25 T38
Ratio of T25 4 MHz component and SDEM with VIN = 300 mVp-p f = 4 MHz VIN = white 50% + CW (15.8 mVp-p) Ratio of 32 fH component and 32.5 fH component Serial 00 OFF 10 (weak) 01 (medium) 11 (strong)
0 -3.7 -9.2 -13.3 -3.5 4.5 2.5 0.5 0 -4 -16.5 -32 -9 -17 2.5 6 6 -8 0 -3.2 -8.2 -11.8 -2.5 6.0 4.0 2.0 0 -3 -15.0 -30 -8 -15 3.5 7 7 -7
0 -2.7 -7.2 -10.3 -1.5 7.5 5.5 3.5 0 -2 -13.5 -28 -7 -13 4.5 8 8 -6 dB dB dB dB dB dB dB dB dB dB dB dB
Nonlinear deemphasis characteristics 1 Nonlinear deemphasis characteristics 2
GNLDE1 GNLDE2
T26A T26A
T38 T38
Input/output response measured with V IN = white 50% + sine wave f = 2 MHz 158 mVp-p
f = 2 MHz, 50 mVp-p CTL 1 2 3 4
Double noise canceler characteristics 1 Double noise canceler characteristics 2 Double noise canceler characteristics 3 Double noise canceler characteristics 4 Double noise canceler characteristics 5 PIC-CTL hard response characteristics 1 PIC-CTL hard response characteristics 2 PIC-CTL soft response characteristics 1 PIC-CTL soft response characteristics 2 Sync tip level Pedestal level White level measurement Simulated V insertion level
GWNC1 GWNC2 GWNC3 GWNC4 GWNC5 GPH1 GPH2 GPH3 GPH4 LVOR
T26A T26A T26A T26A T26A T26A T26A T26A T26A
T38 T38 T38 T38 T38 T38 T38 T38 T38
f = 1.2 MHz, 158 mVp-p, pin 69 open Gr2 bit 8/7 = "10", Gr5 bit 1 = "1" f = 1.2 MHz, 50 mVp-p, pin 69 open Gr2 bit 8/7 = "10", Gr5 bit 1 = "1" f = 1.2 MHz, 15.8 mVp-p, pin 69 open Gr2 bit 8/7 = "10", Gr5 bit 1 = "1" f = 2.5 MHz, 15.8 mVp-p, pin 69 open Gr2 bit 8/7 = "10", Gr5 bit 1 = "1" f = 2.5 MHz, 15.8 mVp-p, pin 69 open Gr2 bit 8/7 = "10", Gr5 bit 1 = "1" f = 1 MHz, 158 mVp-p, Gr5 bit 6/5/4 = "1/0/0" f = 2 MHz, 158 mVp-p, Gr5 bit 6/5/4 = "1/0/0" f = 1 MHz, 158 mVp-p, Gr5 bit 6/5/4 = "0/0/0" f = 2 MHz, 158 mVp-p, Gr5 bit 6/5/4 = "0/0/0"
T26A
T38
T38 video output sync tip (LSYN), pedestal (LPED), white level (LWHT) potential measured with VIN = white 100% 0.5 Vp-p DC voltage at T38 is measured when 5V is applied to T33. Taking this as LVDP, differential with LSYN above is calculated. DC voltage at T38 is measured when 2.7V is applied to T33. Taking this as LHDP, differential with LPED above is calculated. DC voltage at T38 is measured when 1.3V is applied to T33. Taking this as LWHP, differential with L WHT above is calculated. Pin 37 output pulse crest value measured with VIN = 0.5 Vp-p video signal Pin 37 output pulse width measured with VIN = 0.5 Vp-p video signal Delay of output SYNC vs. input SYNC measured with VIN = 0.5 Vp-p video signal
T31 DC level measured
- -50
- 0
- +50 mV
VDP
T26A
T38
Simulated H insertion level
HDP
T26A
T38
-100
0
+100
mV
White insertion level
WHP
T26A
T38
-100
0
+100
mV
Sync separation output level Sync separation output pulse width Sync separation output Pre-delay time 4V regulator FMAGC output level
VSYP PWSYP T SYP V REG VFAGC
T26A T26A T26A T26A T15
T37 T37 T37 T37 T17
4.0 4.35 0.7 3.8 325
4.2 4.65 0.9 4.0 350
4.4 4.95 1.1 4.2
Vp-p s s V
Pin 17 signal amplitude measured with VIN = 150, 300, 600 mVp-p 4 MHz CW
375 mVp-p
Continued on next page
No. 5843-4/25
LA71525M
Continued from preceding page
Parameter [REC mode chroma] REC chroma low-range converter output level REC chroma/FM ratio Symbol Input Output Conditions Ratings
min
CTL 0 1
215 180 -3.7
typ
225 190 -3.0
max
Unit
VOR-14 T28A C/FM
T28A
T14A T14A burst level measured with VIN = 1 Vp-p
235 mVp-p 200 -2.3 dB
standard color bar signal
T14A T18
Down-converted chroma level/FM level ratio with 100% chroma input (RL: 5.1 k) SP/EP and LP T14A burst level ratio with VIN = 1 Vp-p standard color bar signal T56 output amplitude measured with FET probe at VIN = 1 Vp-p standard color bar signal T56 output amplitude measured with FET probe at VIN = 1 Vp-p standard color bar signal VIN = 1 Vp-p standard color bar signal and chroma signal only boosted by +6 dB T14A burst level measured and compared to VOR-14
Burst emphasis amount (NTSC mode) VXO oscillation level (PAL mode) VXO oscillation level (NTSC mode) REC ACC characteristics 1
GBE
T28A
T14A T56 T56 T14A
5.5 300 300
6.0 500 500 +0.2 0.2
6.5 700 700 +0.5 0.5
dB mVp-p mVp-p dB
V VXO-RP T28A V VXO-RN T28A ACCR1
T28A
REC ACC characteristics 2
ACCR2
T28A
T14A VIN = 1 Vp-p standard color bar signal and chroma signal only boosted by -6 dB T14A burst level measured and compared to VOR-14 T14A
-0.5
-0.1
dB
REC ACC Killer input level
VACCK-ON T28A
T14A input burst level measured when output goes off and compared to standard input level, with VIN = 1 Vp-p standard color bar signal and chroma signal being gradually attenuated.
-26
dB
REC ACC Killer output level REC ACC Demodulator input level
V OACCK T28A
T14A
T14A output level measured with spectrum analyzer and compared to VOR-14, in killer condition as described above.
-60
-50
dB
VACCK-OFF T28A
T14A
From killer condition as described above, T14A input burst level is measured when output goes on with input chroma level being gradually increased. This is compared to standard input level.
Input signal: 50% white signal superimposed with 4.4336 MHz 300 mVp-p CW. After checking that T14A output is on, CW frequency is raised until T14A output goes off. Frequency then is gradually reduced. CW frequency when T14A output goes on: f1 350
-20
dB
REC APC Pull-in range 1
fAPC1 T28A
T14A
Hz
REC APC Pull-in range 2 REC AFC Pull-in range 1
fAPC2 T28A
T14A
Same as above, CW frequency is lowered until T14A output goes off. Then frequency is gradually raised. CW frequency when T14A output goes on: f2
-350
Hz
fAFC1
T28A
T51
300 mVp-p, 15.6 kHz pulse train with 5 s pulse width is input. Pulse train frequency is raised until T51 output waveform is impaired. Then frequency is lowered. Pulse train frequency when T51 waveform becomes normal: f1
+1.0
kHz
REC AFC Pull-in range 2
fAFC2 T28A
T51
Same as above, pulse train frequency is lowered until T51 output waveform is impaired. Then frequency is raised. Pulse train frequency when T51 waveform becomes normal: f2
-1.0
kHz
BGP delay time BGP width
tD tW
T28
T37 T60
T37 and T60 waveforms are observed with standard color bar input to T28A
T37 T60
3.1 4.7
3.4 4.9
3.7 5.1
s s
tD tW
A10276
Continued on next page
No. 5843-5/25
LA71525M
Continued from preceding page
Parameter 2 fsc output level 2 fsc duty [PB mode chroma chroma] PB chroma video Output level (PAL mode) Symbol Input T28A T28A T15A T26A Output T58 T58 T38 Conditions T58 level measured in no-signal input condition T58 duty measured in no-signal input condition From T15A in PB and SP mode, a chroma signal down-converted from the PAL chroma noise test signal (SP mode, burst 80 mVp-p) and mixed with a 4 MHz 300 mVp-p sine wave is input. From T26A, a 50% white signal is input. Burst level is measured at T38. PB chroma video Output level (NTSC mode) Ratings
min
360 40 490
typ
400 50 580
max
60 670
Unit
V2fsc D2fsc P Vop-38
440 mVp-p % mVp-p
NVop-38 T15A
T26A
T38
From T15A in PB and SP mode, a chroma signal down-converted from the NTSC chroma noise test signal (SP mode, burst 160 mVp-p) and mixed with a 4 MHz 300 mVp-p sine wave is input. From T26A, a 50% white signal is input. Burst level is measured at T38.
490
580
670
mVp-p
PB chroma Pin 46 output level
Vop-46 ACCP1
T15A T26A T15A T26A T46 T46 T46
Under same conditions as for PVop-38, T46 burst level is measured. Under same conditions as for PVop-38, input chroma level is raised by +6 dB. T46 burst level is measured and compared to PVop-46. Under same conditions as for PVop-38, input chroma level is raised by -6 dB. T46 burst level is measured and compared to PVop-38. Under same conditions as for PVop-38, input chroma level is attenuated and input burst level is measured when chroma output at T46 goes off (compared to standard input 80 mVp-p)
T38 T38
170
200 0.5
230 0.8
mVp-p dB
PB ACC characteristics 1
PB ACC characteristics 2
ACCP2
T15A T26A
-0.5
-0.2
dB
PB killer input level
VACK-P
T15A T26A
T46
-25
dB
Chroma output level in PPB killer condition PB main converter carrier leak
V OACK-P T15A
T26A
T38 measured with spectrum analyzer and compared to PVop-38 in killer condition as described above. Under same conditions as for PVop-38, T38 is measured with spectrum analyzer and 4.43 MHz component is compared to 5.06 MHz component.
-44 -40
-40 -33
dB dB
C LP
T15A T26A
Burst deemphasis (NTSC mode)
GBD
T15A T26A
T46
629 kHz, 160 mVp-p CW is mixed with 4 MHz, 300 mVp-p CW and input to T15A. 50% white signal is input from T26A. Output level during T46 burst interval and during other times is compared.
-5.75
-5.50
-5.25
dB
PB XO output level (PAL mode) PB XO oscillator frequency deviation (PAL mode) NTSC -> PAL conversion V axis burst level
VXO-PP fXOP V BNAP
T15A T26A
T59 T59
T59 output level measured with FET probe in PB mode T59 frequency measured in PB mode: f
300 -9 -1
500 0 0
700
mVp-p Hz dB
+9 +1
From T15A, down-converted chroma noise test signal
T38
mixed with 4 MHz, 300 mVp-p CW is input. From T26A, 50% white signal is input. -45 burst level at T38 is measured and compared to P Vop-38
NTSC -> PAL conversion Burst level ratio
B-NAP T15A T26A
T38
Under same conditions as above, +45 burst level is measured and compared to VBNAP
-2
0
+2
dB
Continued on next page
No. 5843-6/25
LA71525M
Continued from preceding page
Parameter NTSC -> PAL conversion chroma phase Symbol Input T15A T26A T38 Output Conditions 4 MHz, 300 mVp-p CW and 100% chroma signal phase shifted by -90 from burst are mixed and input to T15A. 50% white signal is input to T26A. Chroma phase when pin 67 is 0V is measured and taken as 1. Chroma phase when pin 67 is 5V is measured and taken as 2. P-NAP = 1 - 2 [REC mode/EQ] REC EQ characteristics 1 REC EQ secondary distortion REC EQ characteristics 2 REC EQ characteristics 3 REC EQ characteristics 4 REC EQ characteristics 5 [PB mode/EQ] PB EQ characteristics 1 PB EQ secondary distortion PB EQ characteristics 2 PB EQ characteristics 3 PB EQ characteristics 4 PB EQ characteristics 5 PB EQ characteristics 6 Ratings
min
160
typ
180
max
200
Unit deg
P-NAP
GREQ1 HREQ GREQ2 GREQ3 GREQ4 GREQ5
T22 T22 T22 T22 T22 T22
T18 T18 T18 T18 T18 T18
VIN = 500 mVp-p, f = 4 MHz Input/output response measured
Under same conditions as above, secondary harmonics are measured.
-3
-2
-1 -35 -20 -20
dB dB dB dB dB dB
-40
VIN = 500 mVp-p, f = 627 kHz Input/output response measured VIN = 500 mVp-p, f = 1.07 MHz Input/output response measured V IN = 500 mVp-p, f = 4.5 MHz Input/output response measured VIN = 500 mVp-p, f = 2.0 MHz Input/output response measured
-3.3 -1 -2.3 0
-1.3 +1
GPEQ1 HPEQ GPEQ2 GPEQ3 GPEQ4 GPEQ5 GPEQ6
T15A T15A T15A T15A T15A T15A T15A
T17 T17 T17 T17 T17 T17 T17
VIN = 400 mVp-p, f = 4 MHz Input/output response measured
Under same conditions as above, secondary harmonics are measured.
-2.5
-1.1 -40
0.0 -30 -30
dB dB dB MHz
VIN = 400 mVp-p, f = 627 kHz Input/output response measured VIN = 400 mVp-p High-range trap frequency and gain measured VIN = 400 mVp-p, f = 1.07 MHz Input/output response measured VIN = 400 mVp-p, f = 4.5 MHz Input/output response measured VIN = 400 mVp-p, f = 2.0 MHz Input/output response measured
-1 -11 0 -10 7.8
-25 -30 +1 -9
dB dB dB dB
Continued on next page
No. 5843-7/25
LA71525M
Electrical Characteristics of Audio System
Parameter LINE AMP voltage gain (PB) LINE AMP voltage gain (A1, A2, A3) LINE AMP distortion (PB) LINE AMP Output noise voltage (PB) LINE AMP Maximum output voltage (PB) Output voltage with LINE AMP ALC LINE AMP ALC effect LINE AMP ALC distortion MUTE attenuation Symbol Input T11 T71 T73 T75 Output T77 T77 Conditions Ratings
min
23.0 23.0
typ
23.5 23.5
max
24.0 24.0
Unit dB dB
VGLP VGLR
VIN = -30 dBV VIN = -30 dBV
THDL VNOL V OML VOA ALC THDA MPB MA1 MA2 MA3
T11 -- T11 T73 T73 T73 T11 T71 T73 T75 T7 -- T79 T79 T79 -- -- --
T77 T77 T77 T77 T77 T77 T77
VIN = -30 dBV
Rg = 1 k, DIN audio filter Output voltage for 1% THD
0.01 -80.0
0.1 -74.0 1.5 1.7 -6 1 0.1
0.4 -70.5 1.7 1.9 -5 3 0.5
% dBV
: VCC = 6.8V : VCC = 7.5V
1.3 1.5 -7 0 0.01
Vrms dBV dB %
VIN = -28 dBV
T73 input level reduced from -28 dBV to -8 dBV
VIN = -28 dBV
-10 dBV signals applied to all inputs and MUTE enabled.
80
90
120
dB
EQ AMP open circuit voltage gain EQ AMP input converted noise voltage REC AMP voltage gain REC AMP distortion REC AMP Maximum output voltage Current drain (REC) Current drain (PB) DC offset voltage (PB) in MUTE condition
VGOE VNIE VGR THDR VOMR ICCRA ICCPA MT DCO
T10 T10 T1 T1 T1 -- -- T77
VIN = -66 dBV
Rg = 620, DIN audio filter
58 0.1 13.6 0.001
64 0.8 14.1 0.1 1.5 1.7 11.0 11.5 9.5 10.0 30
70
dB
1.8 Vrms 14.6 0.4 1.7 1.9 13.2 13.8 11.4 12.0 50 mA mV dB % Vrms mA
VIN = -20 dBV VIN = -20 dBV
Output voltage for 1% THD Output voltage for 1% THD Influx current measured at pin 76 (no-signal condition) Influx current measured at pin 76 (no-signal condition) (no-signal condition)
: VCC = 6.8V : VCC = 7.5V : VCC = 6.8V : VCC = 7.5V : VCC = 6.8V : VCC = 7.5V
1.3 1.5 8.8 9.2 7.6 8.0 0
DC offset voltage at pin 77 measured for MUTE ON
No. 5843-8/25
LA71525M Pin Function
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
Power ON/OFF H 1 VCC
1
A-REC-OUT
3.3V
CW, 3.2 Vp-p
100k 15k
A10277
2
A-GND
0V
REC MODE SP-CW LP, EP-0V 3 A-EQ-SW1 3.3V REC MODE NONE
3 55k
REC-LP,EP H
50k
A10278
REC MODE NONE 4 A-EQ-SW2 0V PB, EP MODE SP, LP-CW EP-0V
4 PB-EP H
A10279
REC MODE DC V REF
REC VREF
A10280
5
A-REC-SW
3.3V PB MODE CW 1 mVp-p
5
REC 7V 6 A-HEAD SW-CTL PB 0V DC
PB H
6
50k
A10281
REC DC 3.3V 7 A-EQ-IN 3.3V PB CW, 1 mVp-p
7 VREF 120k
REC DC 3.3V 8 A-EQ-NFB 3.3V
100A
8
A10282
PB CW, 1 mVp-p
Continued on next page
No. 5843-9/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
REC DC 3.3V
200 SL/LP H
9
A-EQ-SW1
3.3V PB CW, 95 mVp-p
9 10 100A
REC DC 3.3V 10 A-EQ-OUT 3.3V PB CW, 95 mVp-p
A10283
VREF
REC DC 3.3V 11 A-LINE-PB-IN 3.3V PB CW 95 mVp-p
11
120k 500
500
100A
A10284
200
1k
200
AGC-TC1
REC 2.3V
DC
200 2.3V 500 1k 500 500 12
12 Carrier Leak Balancer
PB 2.3V
DC
1k 50A(REC)
A10285
REC 1.8V
2k
13 1k
200
13
ACC-FILT
DC
250 50k
PB 1.8V
200A
A10286
REC 2.8V
200
200mVp-p 627kHz
14 REC-C-OUT
14
PB 0V
A10287
650A(REC)
A10288
Continued on next page
No. 5843-10/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform PB-Y-FM 400 mVp-p REC 4.2V PB Y-FM/C-IN C-IN (FROM Pre) PB 3.2V
A10289
Equivalent circuit
200 200 500 15 10k 3.70V
15
500 10k 10pF 100A
A10290
REC 1.6V A-EQ-OUT 16 PM (R03) DC
1k
1k REG
300
PB 1.6V
16 1k 1k
A10291
200
REC 2.6V
FM 730 mVp-p
17
PB-EQ-OUT PB Y-FM 340 mVp-p PB 2.6V
100 17 200
180A(PB)
A10292
A10293
PEC Y-FM 730 mVp-p REC 1.9V REC-Y FM-OUT
18 30k
A10294
A10295
200
18
100
PB 1.9V
REC 4.2V
REC PAUSE 2.5V 19 REC-H-OUT DC
22k 20k
19
EE or PB 0V
50k
30k
A10296
Continued on next page
No. 5843-11/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
REC 4.7V
FM 700 mVp-p
8k
20 500 500
20
PB-Y-FM-IN (FROM EQ) PB 2.5V
PB-Y FM 320 mVp-p
3.25V
8k
100A(PB)
A10297
A10298
125A
REC 1.6V
500 200
2k
500 1k
21
AGC-TC2
DC
21 30k
PB 1.7V
REC-ON
A10299
REC 0V PB-EMITTER -PEAKING PB 2.6V
DC
200
22
22
340mVp-p
200 50k
A10300
A10301
500 mV
REC 2.1V
24 200
A10302
2k
2k
2.1V
23 MAIN-EMPH OUT PB 0V
23 500
1k 2pF
A10303
24
00 mVp-p
REC 2.1V 24 MAIN-EMPH FILTER
200
2k
2k
2.1V
A10304
23 500
1k 2pF
PB 0V
DC
A10305
Continued on next page
No. 5843-12/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
640A 200
A10306
500mVp-p
REC-Y REC 1.6V
25
500mVp-p
MAIN-DE-EMPH. OUT PB 1.2V
A10307
2.5k 25
A10308
500mVp-p
REC 2.9V
A10309
30k 15k
15k
200
26
CLAMP-IN
500mVp-p
PB 2.8V
A10310
20k 26
500
400A
A10311
27
Y-GND
0V
28
REC VSYNC 1.7V 28 VIDEO-IN1
1.0Vp-p
200
A10312
50k 10k
2.3V
PB 0V
DC
22A 24A 24A
A10313
7.5k
500 29
REC 2.6V FBC-FILT (Feed Back Clamp)
200
29
DC
500
500 20k
PB 2.6V
130A
A10314
30
REC VSYNC 1.7V 30 VIDEO-IN2
1.0Vp-p
200
A10315
50k 10k
2.3V
PB 0V
22A 24A 24A
A10316
Continued on next page
No. 5843-13/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
REC 4.1V
31
31
REG
DC
23k
PB 4.1V
10k
A10317
32
REC VSYNC 1.7V
1.0Vp-p
200
A10318
50k 10k
32
VIDEO-IN3
2.3V
PB 0V
22A
50A 50A 33 1k 1k 10k
24A
A10319
0 to 0.8V : Through 1.0 to 2.2V : Character Ins. 2.5 to 3.2V : QH Ins. 3.8 to VCC V : QV Ins.
33
QV/QH-INS CHARA-INS
50k 30k
30k
A10320
REC VSYNC 1.7V 34 VPS-OUT
1.0Vp-p
200
A10321
34
PB 0V
470A
A10322
1.0Vp-p
4V
REC 2.3V
A10323
35 7.5k
35
VIDEO-AGC-IN
7.5k 17k
PB 3.1V
740A
A10324
Continued on next page
No. 5843-14/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
36
Y-VCC
5V
DC
20k
500
500
4.2V
20k
37
SYNC-OUT
0V
A10325
200 50k 10pF 37
A10326
100
100
REG 15.5k
200
2.1Vp-p
38 VIDEO-OUT
VSYNC 0.8V
38 11k
A10327
26k 620A 1.8A
A10328
1k
1k 39
REC 3.1V
39
VCA-FILT
DC
500 9k
PB 3.1V
200A
A10329
350 mVp-p
15k 200
REC 2.8V VCA-IN (CLAMP)
A10330
1k 15k
40
350mVp-p
40
500
PB 2.8V
A10331
100A
A10332
41
VCC2
5V
DC
Continued on next page
No. 5843-15/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
350mVp-p
REC 1.8V
A10333
350
42
Y-CCD-DRIVE
370mVp-p
PB 1.8V
A10334
42 370A
A10335
NTSC MODE 4.2V 43 NTSC-H OUT WITHOUT NTSC MODE 0V DC
200
43 50k 50k
A10336
REC 1.7V
1k
1k
REG
44
PQ 2 (RO2)
DC
300
PB 1.8V
44
1k
1k
A10337
4k
1k
REC 1.8V
210mVp-p
65k
45
PB CHROMA IN
45
A10338
PB 1.9V
35k
A10339
REC 0V PB CHROMA OUT
100
210mVp-p
46
46
PB 2.0V
A10340
400A (PB)
A10341
Continued on next page
No. 5843-16/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
47
C-VCC
5V
DC
150mVp-p
REC 2.8V
A10342
48
C-CCD-DRIVE2
48 440A (PB)
130mVp-p
PB 2.8V
A10343
A10344
500
200
500
REC 4.0V
200
49
49
SLD-FILT
DC
22k 1k 51
A10345
PB 4.1V
2k
150mVp-p
REC 2.9V
A10346
250
50
C-CCD-DRIVE 1
130mVp-p
PB 2.9V
A10347
50 440A
A10348
500k
200
500k
REC 4.0V
H
10mVp-p
A10349
49 200
51
AFC/APC-FILT
22k 2k 1k
PB 4.0V
Field
A10350
51
A10351
97A
140mVp-p
52
C-CCD-IN
3.2V
52 10k 2.5V
A10352
500
A10353
Continued on next page
No. 5843-17/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
P.A.STOP
53
53
PA STOP-TR-SW
0V
DC
H
A10354
50k
54
REC-APC-FILTER
2.1V
50k
H
A10355
5k
2.1V 70k 3rd H
54
A10356
55
REC 4.0V
600mVp-p
A10358
200 200 500 2k
55
VXO/XO-IN
PB 3.9V
600mVp-p
62A (VXO)
A10358
90A
650A 340A (XO) (VXO)
A10359
REC 2.5V
600mVp-p
A10360
100
200 100
900
2k
56
VXO/XO-OUT
100k 56 300k
PB 2.5V
500mVp-p
900A 100A (XO) (XO)
A10361
500A
A10362
57
C-GND
0V
DC
REC 1.5V 2 fsc/PB-H OUT PB 2.8V
400mVp-p
5k
A10363
200
58
200 58
400mVp-p
A10364
500
A10365
Continued on next page
No. 5843-18/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
1k REG
1k
REC 1.5V RL (RO4)
DC
59
300
PB 1.5V
DC
59
1k
1k
A10366
60 200
60
BGP-OUT
SYNC+BGP SYNC 1.4V (typ) BGP 4.0V or MORE
50k 20k
A10367
1k
200 5k
Color 2.0V
61
KILL-FILT
DC
1k 1.66k 61
A10368
killer 3.0V
260
2.5V
ACK-OUT MODE 62 ACK/SLD OUT SLD-OUT MODE
KILLER MODE 4V or MORE COLOR MODE 0V
200 KIL H
2k
2k
20k SLD PULSE 62
200A 0A 1H
A10369
A10370
50A
15k 25k
63
SERIALCLOCK-IN
3.0V
5V 1.6V 0V
A10371
3V 63 300 60k
A10372
Continued on next page
No. 5843-19/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
50A
15k 25k
64
SERIALDATA-IN
3.0V
5V 1.5V 0V
A10373
3V 64 300 ACK
A10374
60k
REC 1.6V PQ1 (RO1) PB 1.6V
65
1k
1k REG
65
DC
300 1k 1k
A10375
0.8V
1k
85k 66 1k
66
C-ROTARYPULSE-IN
0
A10376
20k
A10377
0.8V
67
1k
67
CSC-PULSE-IN
20k
0
A10378
A10379
+45 4V or MORE 68 PAL-PULSE +45 1V or LESS
50k 68
A10380
REC 2.1V
17k 40k 69 40k 2.2k 500 23k
69
NC-CTL
DC
PB 2.1V
A10381
Continued on next page
No. 5843-20/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform
70 10k
Equivalent circuit
70
A-MUTEON/OFF
MUTE 3V or MORE
DC
45k 2.5V 45k 100A GND
A10382
VREF
REC CW, 95 mVp-p
120k 71
71
A-LINE-IN1
3.3V
PB DC 3.3V
100A
A10383
VCC
REC: ADAPTIVE
200
72
A-ALC-DET
0V
150 72 2k 10k
A10384
PB DC 0V
VREF
REC CW, 95 mVp-p
120k
73
A-LINE-IN2
3.3V
73
PB DC 3.3V
100A
A10385
VCC 43k 500 500 500 39k 100k GND
A10386
74
A-V REF-FILTER
24k
3.3V
DC
74 22k
Continued on next page
No. 5843-21/25
LA71525M
Continued from preceding page
Pin number Pin name Standard DC voltage Signal waveform Equivalent circuit
VREF
REC CW, 95 mVp-p
120k
75
A-LINE-IN3
3.3V
75
PB DC 3.3V
100A
A10387
76
A-V CC
7V
DC
Power ON/OFF
H
VCC
77
A-LINE-OUT
77
3.3V
CW, 1.4 Vp-p
75k 10k
A10388
78
A-ALC DET-IN
0V
CW, 1.0 Vp-p
78 500
A10389
VREF
REC CW, 745 mVp-p
79
120k 500
79
A-REC-IN
3.3V
PB DC 3.3V
100A
A10390
VREF
VREF 1.8k 500 80 7.3k
REC CW 745 mVp-p
120k
80
A-REC-NFB
3.3V
PB DC 3.3V
100A 1
A10391
No. 5843-22/25
0.01 F
14 VSS 2FSC/PB-H OUT BGP OUT 1H/2H DL 3
+
13 1H DL
VCC(+5V) 1
10 F
CHROMA OUT SECAM DET
10 12 11 NT:H 3FSC CLK OUT IN
9
0.01 F
8
0.1 F
LC89980
7
0.01F
VDD 2 5
N.C. 4
N.C. 6
0.01F 1 k
100 H 47 F
+
0.1 F
TO/FROM MI-COM.SERVO
100 H
PB SECAM CHROMA IN
1.8 k
1 F
1 F
+ +
8.2 k
1.2 k
SERIAL CLOCK IN
0.047F
+
47 F
0.1 F
0.01 F
4.43
0.047 F
ACK OUT
0.01 F
+
0.022 F
SERIAL DATA IN
10 F
1 F
VCC2(+5V) (POWER SAVE MODE)
64
+
63 VXO1 KIL DET LPF VCO INV SLD LPF P 37
47F
62 ACK OUT AMP R
1 F
+
61
57 56 60 59 58 BGP RL 2FSC/PB-H C-GND REC APC DET YNR 39 VIDEO AMP 38
10 F 1 M
55
54
53
52
51
50
49
48
65 PQ1 CLP 40 NAP KIL B.D. R
47 46 C-VCC BPF
45
44 43 PQ2 P
42
41 VCC2
C-ROT IN COMB AFC DET TH P Y-VCC 36 VIDEO AGC 35 34 QV/QH INS CNC SYNC SEPA FBC R P AGC DET DETAIL EMPH P R CLAMP RP 28 MAIN EMPH N.L. EMPH R P CLAMP 33 32
0.1 F
+
+
51 k
C-ROT 66 IN
0.1 F
+
51 k
67 CSOP IN PB APC DET R PB BGA-B BPF1 SUB CONV P SUB BPF BPF2 YC MIX ACC AMP MOD LINE AMP P REC P C-LPF R KIL 13
0.047 F
VIDEO OUT C-SYNC OUT
0.01 F
COLOR SEQUENCIAL COMPENSATOR PULSE IN PAL-PULSE OUT SERIAL DECODER PB BGA-A R.A B 1/2 DHP NC N.L. DE-EM
10 F
68 PAL-PULSE P
69 NC-CTL
MUTE CTL
82 k
0.1 F
70 MUTE CTL
AUDIO IN1 P R ALC VREF ALC DET ACC DET MAIN CONV REC BGA R PIC CTL
71
100 H
SUB TITLE DECODER VPS OUT QV.QH.CHARA.IN VIDEO IN3
6.8 k
+
22 F
72
Block Diagram and Sample Application Circuit
82 k
LA71525M
AUDIO IN2
2.2 M
6.8 k
0.1 F
73
+
AUDIO IN3 R P
82 k
33 F
REG
74
31
3 2 1
+
47 F 0.1 F
6.8 k
0.1 F
75
CLAMP
30 29
0.1 F
+
VIDEO IN2
1 F 0.1 F
47 F
VCC+7V MUTE
+
76 A-VCC
LINE OUT
0.1 F
+
15 k
4.7 F
77
VIDEO IN1
13 k
1.8 k
2SC3331
0.1 F
79
FM AGC PB-EQ
REC EQ
DOUBLE LIMIT
CLP R P MAIN EMPH
26 25
+
REC
Y-GND
78
27
1 F 1 k 4.7 k
PB-EP REC
80
REC AMP
A-GND
REC-EP.LP
3.3 k
EQ PB-LP.SP AMP 7
1 F
8.2 k
+
1
+
2
3
4
5
HD SW 6 8 9 10 11 14 15
BAL TC1 12
PM 16
17
SUB REC DEMOD LPF HIGH OUT PEAKING 23 21 22 18 19 20
22 F 0.01 F 120 H
+
24
2.7 k
200 pF 1.3 k 56 pF
0.1 F
12 k
390
10 F
33 pF 47 H
+
3.3k 43 pF
0.01 F 330 k
+
0.022 F
1 k
180 22 F
AE
10
390
820
0.01 F
390 pF 680
M
REC SECAM CHROMA IN PHASE COMPENSATION
2.2 k
220 pF
FE
+
+
0.022 F
0.01 F
H.SW.P.IN 12 11 10 9
REC H REC C IN REC FM IN
10 k
2SC3331 1 k 2SA1318
PB-L
8
7
PB YC OUT
6
5
C SYNC IN
4
HSWP IN
3
2
1
TRICK H
R/P
22 k
2SC3331 1 k
No. 5843-23/25
13
LA70010 4HD AMP
24
A10392
0.01 F
0.01 F
14 VSS 1H/2H DL 3 N.C. 4 5 7 N.C. 6 1H DL
13
10 12 11 NT:H 3FSC CLK OUT IN
9
8
0.1 F
LC89980
SW51 321 0.01 F
1
VDD 2
0.01 F
47 F 100 H
+
T60
TO/FROM MI-COM.SERVO
T46
10 k
0.1 F
Test Circuit Diagram
1.8 k
0.01 F
1 k
100 H
T62 T56
ACK/SLD OUT
4.43 PAL
T51
1 F
0.022 F
+
+
0.047 F
SW49
0.047 F
47 F
T63A
1.8 k
SERIAL CLOCK IN
+
8.2 k 1 F
0.01 F
+
0.022 F
2.2 k
1 F
VCC1
1 F
0.022 F
T64
SERIAL DATA IN
+
5V 1 2 SW41
64
+
63 VXO1 KIL DET LPF VCO INV SLD LPF P 37 Y-VCC 36 VIDEO AGC 35 34 QV/QH INS CNC SYNC SEPA FBC R P AGC DET P DETAIL EMPH R CLAMP RP
Y-GND
+
62 ACK OUT AMP R
1F
61
57 56 60 59 58 BGP RL 2FSC/PB-H C-GND YNR 39 VIDEO AMP 38
0.1F 47F
+ +
55
54
53
52
51
50
49
48
65 PQ1 CLP
10F 1.0M 470F 51
+
46 47 C-VCC BPF 40 VIDEO-OUT
75
45
44 43 PQ2 P
T38A
42
41 VCC2
T66A
C-ROT IN KIL B.D. R
C-ROT 66 IN COMB P
NAP
75
T38 T37
T67A
H.SW.P IN PB APC DET R N.L. DE-EM 1/2 PB BGA-B BPF1 P R SUB CONV P SUB BPF BPF2 YC MIX R R PIC CTL P ALC VREF REC BGA DHP NC AFC DET TH
67 CSOP IN
SW67
68 PAL-PULSE SERIAL DECODER PB BGA-A R.A B P
SYNC-OUT
100H
123
0.01 F
69 NC-CTL
2
SW70
70 MUTE CTL
SW71
1F
1 k 1
0.1 F
71
LA71525M
SW72 22 F
+
SW73B
72
33 CLAMP
REG
T33
QVQH INS 32
T31
T73A
1 2
3
1
2.2 M
T72
2 SW73A
0.1 F
73
0.1F
T32A
VIDEO-IN3 31
3 2 1
+
1 k
+
47F 0.1F
1
+
2
SW75
33 F
74
0.1 F
75 ALC DET MOD LINE AMP P REC P C-LPF R KIL 13
0.047 F
CLAMP
30
0.1F
T30A
VIDEO-IN2 29 28
0.1F
+
VCC2
7V
1 k
0.1 F
4.7 F
76 A-VCC MUTE
ACC DET MAIN EMPH N.L. EMPH
R P ACC AMP MAIN CONV
1F
T28A
15 k
T77A
+
4.7 F
77
VIDEO-IN1 27
T26
T79A
1
SW79
0.1 F
79
REC PB-EP
FM AGC PB-EQ
REC EQ
DOUBLE LIMIT
CLP R P MAIN EMPH
26 25
1F
+
1 2
SW80 10 F
80
A-GND
REC AMP EQ AMP 7
1 F
+ +
+
2
13 k
78
REC
2
T26A
1 SW26 1 k 4.7 k 1.3 k 200 pF
REC-EP.LP
1
+
2
4.7 F 0.1 F
3
4
5
HD SW 6 8 9 10 PB-LP.SP 11 14
0.022 F
BAL TC1 12
15
PM 16
17
2.2 k
SUB REC DEMOD LPF HIGH OUT PEAKING 22 23 19 20 21 18
REC-H OUT
0.01 F 22 F
+
24
2.7 k
56 pF
T24 T25
18 k
1 k
12
620
PM-IN
12 k SW11 312
10F
T10A T11A
PM-OUT
SW20
43 pF
0.01 F
SW24 SW22
1 k
10 k
T14A
T15A
T20A
120 H 3.3 k
T17
T18
T19
390 pF 680
SW7
39 k 0.022 F
1 k 0.01 F
T1A
+
10 F
330
4.7 k
SW8
1 k
+
39 k
T7A
330 k
0.01 F
T23
2.2 K
0.01 F
REC APC DET
No. 5843-24/25
A10393
LA71525M
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of March, 1999. Specifications and information herein are subject to change without notice. PS No. 5843-25/25

▲Up To Search▲

Price & Availability of LA71525M

	To Download LA71525M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .